Once you get it blinking just push buttons you'll find the ones that do what you need. If that doesn't work, your best bet is to look up the watch model and google it, or better, go to the manufacturers website for a manual. When an 'H' appears to the right of the time, these are the military hour choices. Answer well, depending on what model of arnette watch, you may want to take a look on the back, where it says mode, set. Some watches also let you set the time when you … put in the battery. The battery is fine, the seconds are ticking away, but none of the side buttons work. In my case the button I have to press is the lower right one.
If that doesn't work try pressing two buttons simultaneously You might have to be in a certain mode in order for this to work. The stopwatch is still running in the background. The light doesn't come on and nothing happens with any of the others either. To display the current elapsed time, press S2 button again. Aug 08, 2008 for a watch face that has a day of week, date, and moon calendar: There are two click points on the set-pin. Press mode again to get back … to the standard time telling function. Holding down the button will speed up the process.
Holding down the button will speed up the process. Press S1 button again to resume from where it left off. How To Set the Time For A Timex Watch: First, push the mode button on the bottom left corner for 3 seconds. To set the analog dial, just wait until the second hand is right on 12, and then pull the crown outward. From the normal time screen. When you are done just press mode again. To set the digital part, the lower right button means set, so hold that down until the seconds start flashing.
When seconds start flashing, hit a different button to switch to minutes, then hours. The only thing that did work was pressing all four of the buttons simultaneously, which seemed to totally reset the watch. When done, just hit the bottom right button again. After pressing the lower left button three times and the lower right button once you are setting the hour of the time. When the hour is set the watch goes through two sets of 24 hour choices, one set for regular time, on … e for military time.
Rotate the crown until the time on the clock is right, and when you push in the crown, the watch will start running, so try to push the crown … in at the top of the minute. You just make sure it's in a place where it can hear the radio signal from Colorado, and if you wait long enough, the watch sets itself to the correct date and time. Also if you press and hold the lower left button for at least 3 seconds you can change the way the clock displays date and time. The date is now set and will change on time, approx. Posted on Dec 02, 2008 I am having the same problem.
When the correct hour appears press the lower right button. Change from alarm to date to time by pressing the upper left butt … on again. So now I can't even see the correct time anymore. Mar 15, 2010 hold the left, bottom button marked. The Sportline might be the same or similar. The transmissions are spaced at 4 times per day, so … if the watch hasn't set itself within six hours, and continues to miss updates, then it's either broke or not receiving the radio signal in the spot where you have it situated. Then when time starts flashing, you can change the flashing value by pressing the upper right button.
Then you can press the upper right Start button to re-start the seconds at zero. When you are done setting the time and date press the lower right button and that's all. The split time of the registered lap will be displayed. To set the minutes, hours, days, and date and 12-24-hour , press the mode button, which is at the lower left, and press the upper-right Start button to change the values When you are done setting the digital part, press the lower-right set button again. The crown is the big knob at the 3-0'clock position. Do it later withstep 1 and 2!! To edit another value you press the lower left butto … n and another value will flash.
Once you get this first position set the date to 1 day before the date you want, now pull the stem out to set the time of day, go thru 1, 24 hour cycle to set the date you want and time of day. The problem is it reset but didn't fix the buttons. The watch will go into the new mode after about 3 secs. Holding down the button will speed up the process. What you have to do is to press and hold one of the buttons for at least 3 seconds.