Pass wire ropes between the 1st and 2nd track rollers from the front and between the 1st and 2nd track rollers from the rear. If it is milky white, it is necessary to change the grease. Do not simply rely on the monitor when carrying out checks before starting daily inspection. Install mirror 1 to support 3 ,then tighten lock bolt 2. On the 2-Way Attachment Select Menu, select one of the two set values for the oil flow, then press switch F6. Keep the top surface of the battery clean and check the breather hole in the battery cap. The ground under the machine may collapse and cause the machine to fall.
Operate the lever to the end of its travel and hold it in position for 30 seconds. Using a grease pump, pump in grease through the grease fittings shown by arrows. If the bucket or attachment has any hydraulic connections to the machine these must be disconnected before proceeding. After confirming low oil temperature, remove the plug from the outlet and inlet port respectively. If it is desired to change settings for the maintenance interval, have your Komatsu distributor change the settings.
Always wear protective equipment such as protective glasses and mask. Select the method of operation as desired. When setting to the breaker mode, always press function switch F6. Japanese, English, Chinese, French, Spanish, Portuguese, Italian, German, Russian, Turkish, Indonesian, Thai 1. F5: Returns to previous screen. Engine oil change Engine oil filter change Fuel main filter change 1000 Fuel pre-filter change. M : 125 mm q If the side view mirror does not move smoothly when adjusting its angle, loosen mirror securing bolt 4 and mir-.
This will have an adverse effect on the environment, and will also have an adverse effect on the internal structure of the engine. The Demolition Digging Equipment allows easy removal and separation of demolished material. This procedure includes the following basic steps: 1. Such an act may cause a seri- ous bodily injury or fire. Connect the individual quick connector lines, in accordance with the diagram and table. If any problem is found, contact your Komatsu distributor. It will contact the undercover or frame and cause damage.
Always put blocks under the track to prevent the machine from moving, and dig the work equipment into the ground. Display A at low temperatures: Monitor background D is white Display B at correct temperatures: Monitor background D is. Lower the work equipment to the ground. Connect the booster cable as follows, in the order of the numbers marked in the diagram. Place the bucket in contact with a flat surface. However, when performing bucket operation, perform digging while gradually raising the boom.
Attach additional warning tags around the machine if necessary. Run the engine at idling for a short time, then stop the engine and check again that the oil level is between the H and L marks on dipstick G. When disposing of the accumulator, the gas must be released. Contact your Komatsu dis- tributor for repairs. If working mode selector switch 1 is pressed, the Working Mode screen is displayed on the monitor. Even if the engine starts, wait for the engine oil pressure monitor to go out.
F3: Moves to next item 1 line down. On the standard screen, press switch F6. If the indicator goes beyond red range A during opera- tions, the overheat prevention system is actuated. Lower the work equipment to the ground and set the machine in a stable condition. Type of work R - Recommended work. On the 2-Way Attachment Oil Flow Setting menu, it is pos- sible to change the oil flow setting. If it is not necessary to change the minute setting, press switch F6.
In P and E modes, the power max function can be actuated for a maxi- mum of only 8. Always replace them with new parts. A genuine Komatsu filter cartridge is recommended for use. F3: Moves to next item 1 line down. Obey all state and local laws governing the weight, width and length of the load. If the knob is turned counterclockwise, the bass sound is reduced. Please contact your Komatsu distributor to have this work performed.
Fuel is highly flammable and dangerous. This may cause an explosion. However, for machines equipped with a full roller guard for the track roller, pass the wire rope under the track. For link pin portion B , install the bucket with O-ring 3 fitted in the standard groove. If there is any damage, replace with new parts.