The manual describes the model with the maximum equip- ment at print time. Remove the four threaded clips. Note the anti-clockwise direction of the numeration. Besides tyre can be punctured more easily than a new being illegal, riding a motorcycle with. F Steering damper adjustment §5.
In any case, never exceed the speed limits riding the vehicle always requires the utmost care. After a preliminary check approx. Multifunction display Thermometer Speedometer Displays the coolant temperature in degrees centigrade Measures the speed of the vehicle. Safety - Visual and acoustic Turn indicators § 3. Do not change the display while dri- ving. The chain should be correctly inserted into the tool and kept in place by rods 3. The shock absorber contains high-pressure gas.
The vacuum tubes are located on the right and left side of the vehicle. Relying on the advice of persons other than a qualified riding instructor, even if possessing specific knowledge, may prove to be useless or even dangerous, especially if the practical training takes place in an area open to traffic. When the engine is running, pressing the button selects the dis- play functions. Always keep up to date the registration data of Protective clothes do not afford com- your motorcycle. Do this in stages to sta- bilise the liquid level. Steering pin tightening Screw down, without tightening, the screw ring of the steering pin.
Never remove the battery seal caps nor block the breather opening. Remove the right air intake conduit. Insert the rear brake pump in a protection cap, fixing it with an elastic on the frame. To check this component it is necessary to identify the relative connector positioned as shown in the figure, inside the frame on the left side of the motor- cycle. If the spacer is in good condition, reinsert it onto the fork from the right side.
For reassembly, insert the pinion to end stroke. Protect the steering head with padded material and rest it over the dashboard. This signifies that the lack Use the recommended coolant. Repeat the above operations until the fluid reaches the minimum level in the reservoir. Remove the fairing side panel, sliding it off from the front side.
Loosen the fork spindle tightening screw, turning it once. Do not dispose of the used oil in the environ- ment. Check that the two small overflow tubes 2 remain out- side of the fuel tank. Remove the right frame plate. Setting the display functions The following functions can be set: clock, speedometer and thermometer units.
Remove the valve 2 , pulling it from the support out- ward from the right side with the aid of a screwdriver. Using the special spanner as indicated in the figure, move the eccentric adjuster nut backwards or forwards respectively slackening or tightening the chain, until the correct play is reached as described previously. For the assembly operations, assemble in reverse order of removal. Unscrew the two nuts 4 relative to the manifold tube couple. Push down to remove the pump from the reference pin. Remove the phase sensor fixing screw 3.
Before adjusting the rear suspension, shut off the engine and wait until the exhaust pipes have thoroughly cooled. Preliminary cleaning - Before lubrication, the dirt accumulated on the chain must be dissolved using kerosene. Grease the pin: Recommended grease: Agip Grease 30 For the reassembly of the lever tighten the pin. At the same time, the instrument starts recording the time taken to cover the second lap. The use of worn O-Rings can lead to a leaka- ge of petrol from the tank with a consequent risk of fire for the vehicle.
Remove the left frame plate. Pull out the burnt-out bulb. To separate the air manifold from the side panels, removing the two fixing screws 2. Every time ment according to the procedures the chain is replaced, you must always shown in this paragraph. Move the tube support plate outward to facilitate the following operations. Disassembly of the frame head steering sleeve Utilising the special tool, remove the steering screw ring.
Identification data required to provide the engine serial number, the 1 vehicle identification number colour code and the key identification. Remember to put the gear lever in the neutral position before restarting the engine. Top up with fresh fluid and carry on with the operation until fluid of a different colour fresh flows out. Apply the lubricant after cleaning. Extract the rear part of the support first A then grad- ually withdraw the support from its front seat fixing B. Operating as shown in the figure, slightly lift up the cylinder head cover.