Replace using only Weber authorized replacement manifold assembly. Lift the manifold, bracket and cooking box slightly and hook the tab of the bracket onto the frame brace. Remember to always open the tank valve Very, Very Slowly. Insert hinge pins from the outside. The hissing sound can just be the flow of gas thru the regulator. Call the Weber Crossover rail Customer Service Center toll free 1-800-446-1071 to Front frame receive immediate assistance.
Regulator manufacturers tell us they should be replaced after 25 years. I would first check the main tubes and cross tube carefully for places that are rusted through. Push the casters firmly into the inserts in the ends of the caster legs. Fill water pan, place it in This residue need not be removed and will not adversely affect the function of your Weber Gas Barbecue. Our knowledgeable Customer Service staff is prepared to help you with any problems with parts or assembly. Any or all of the the above should solve your problem. Another problem, though uncommon for a new grill is a defective regulator.
Place the caster frame onto the tabs of the left frame with the dimple to the inside. Unlike the standard issue stainless grids generally found today, which are typically low grade stainless and sometimes hollow, or coated carbon steel, our premium grids are made from solid high quality stainless steel rods. That's got to be a bummer. Check by pushing down and turning clockwise. Do not use charcoal or lava rock in your Weber Gas Barbecue. Did the burner light and does th eflame height look correct? Look at the guy walking on the right side in his hand is a regulator, that's what should be attached to it if it is truly a propane grill. Considering buying this used grill, but can't identify it.
Me, I wouldn't touch it, to many unknowns. Would really appreciate the help! Just look at the weight of one of these grids, almost 6 pounds of solid stainless each. As a safety precaution you should recheck all fittings for leaks before using your Weber Gas Barbecue. A little time and some advice here and you will have a great grill. Genesis Gas Barbecues are covered under the following patent nos. If so, you solved the problem.
Problem Check Cure Side burner does not light. Place the wheel frame onto the tabs of the right frame with the dimple to the inside. Allow the slide bar to hang down. The serial and information as to the type of gas it uses should be underneath the control knob plate. Place your hand underneath the bracket.
Jul 04, 2011 The regulator that comes with Weber grills shuts the gas flow off if it detects the slightest leak. Swing the rod up so you can slide the rod all the way inside the locking tab. While we give much attention to our products, an occasional error may occur. Premium quality heavy duty stainless steel for some Weber grills. If this does not work, you can buy or borrow a similar, but working hose. Disconnect the tank an reconnect. Turn frame assembly right side up.
If so, light the remaining burner the identical same way. As a last resort, contact Landmann, the manufacturer Hope this helped you. Sounds like this one is very problematic. If that didn't solve the problem. This blocks the normal gas flow, and can cause the gas to flow back out of the air shutter. The entire lamp assembly has internal wiring to it and the wires for the low and high beams feed through the housing at a different location, not to worry, you don't need to mess with those wires. Has wooden slats for tabletop.
Clean with soap and water. Aug 13, 2011 It's simply a vapor lock. Wait 5 minutes and reconnect the hose to the tank. Open the lid and wait five minutes before attempting to relight, using the lighting instructions. I'm wondering about the possible other unknowns for fifty bucks? Slip the bolts on the back of the fuel scale assembly through the two small holes in the tank panel. Check connections with soapy water for any leaks.
Do this even if barbecue was dealer assembled. Order from Weber-Stephen minutes to allow the gas to clear if the Products Co. If a part is Left end panel missing, do not go back to the store. Have your Proof of Purchase handy and call Weber 1-800-446-1071. If you smell gas however, then you should replace it. They can nest in the venturi section of the burner tubes. To help insure that you choose the correct replacement parts, we highly recommend that you measure your original parts and compare them to what we have listed below.
Brand new grill get it assembled and find one wrong door. The spider traps, if you have them, are little plastic cages and the edges snap together. Set the long Flavorizer Bars side to side in the lower position, then set the short Flavorizer Bars front to back in the upper position in the cooking box. The best way to find the correct replacement Cooking Grids for your Weber grill is to. Disconnect the hose from the tank and wait 5 minutes. Holes can lower the pressure in the tubes and make them difficult to light try just turning on and lighting the front burner. Just look at the weight of one of these grids, over 8 pounds of solid stainless each.